Consider a bar of varying cross-section of uniform strength subjected by a longitudinal stress \u03c3 as shown in Figure 12.10. Now consider a small element of axial length \u03b4x at a distance of x from smaller end. Let area of cross-section at section x be A and at section x + \u03b4x be A + \u03b4A. For the element of length \u03b4x to be in equilibrium, the total downward force must be equal to the total upward force acting on it.<\/p>\n\n\n\n
Figure 12.10 Varying Cross-section Bar of Uniform Strength<\/p>\n\n\n\n
Weight of length \u03b4x + Tensile stress at section x \u00d7 Area at section x = Tensile stress at section (x + \u03b4x) \u00d7 Area at section (x + \u03b4x)<\/p>\n\n\n\n
Here, \u03b4W is vertical weight due to weight of free body = \u03c1 \u00d7 g \u00d7 A \u00d7 \u03b4x where \u03c1 is the density of material of the bar.<\/p>\n\n\n\n
On integration, between area A1 and A<\/p>\n\n\n\n
Let de be the extension in a small length dx.<\/p>\n\n\n\n
Example 12.6: A bar of uniform strength is shown in Figure 12.11.<\/p>\n\n\n\n
Its length is 5 m, diameter at bottom edge is 100 mm, weight density of bar is 0.07644 \u00d7 10\u22123 N\/mm2. It is subjected to a uniform stress 0.6 N\/mm2. Find the diameters at the top and at the half of its length.<\/p>\n\n\n\n
Figure 12.11 Bar of Uniform Strength<\/p>\n\n\n\n
Solution:<\/p>\n\n\n\n
Given: d = 100 mm, l1 = 5 m, \u03c3 = 0.6 N\/mm2, pg = 0.07644 \u00d7 10\u22123 N\/mm2.<\/p>\n\n\n\n
12.5 STRESS AND STRAIN IN COMPOUND BAR
Any tensile or compressive member which consists of two or more bars or tubes in parallel, usually of different materials, is called a compound bar. Figure 12.12 shows an example of compound bar; it consists of a tube and a rod of different materials.<\/p>\n\n\n\n
Since the initial length of tube and rod are same, it will remain together after application of external force P. Therefore, the strain in each part must be same. Suppose the loads shared by tube and rod is P1 and P2 out of total load P.<\/p>\n\n\n\n
Figure 12.12 Compound Bar<\/p>\n\n\n\n
where A1 and A2 are cross-section of tube and rod, respectively; E1 and E2 are modulus of elasticity of tube and rod materials, respectively.<\/p>\n\n\n\n
On solving Eqs (12.1) and (12.2), we get<\/p>\n\n\n\n
12.6 STRESS AND STRAIN IN AN ASSEMBLY OF TUBE AND BOLT
Figure 12.13 shows stress and strain produced in a compound rod.<\/p>\n\n\n\n
Figure 12.13 An Assembly of Tube and Bolt<\/p>\n\n\n\n
where r subscript is used for rod. Rod is subjected to tensile stress and tube is subjected to compressive stress.<\/p>\n\n\n\n
The reduction in length of tube and extension in rod may be different due to difference in materials of tube and rod.<\/p>\n\n\n\n
Example 12.7: A steel rod of 20 mm diameter passes centrally through a steel tube of internal and external diameters of 25 and 30 mm, respectively. The tube is 800 mm long and is closed by rigid washers of negligible thickness which is fastened by nuts threaded on the rod. The figure of the assembly is shown in Figure 12.14.<\/p>\n\n\n\n
Figure 12.14 Compound Bar as an Assembly of Tube and Rod<\/p>\n\n\n\n
dr \u2212 Diameters of steel rod = 20 mm
di \u2212 Internal diameters of tube = 25 mm
d0 \u2212 External diameters of tube = 30 mm
l \u2212 Length of tube = 800 mm
<\/p>\n\n\n\n
The nuts are tightened until the compressive load on the tube reaches 25 kN, calculate the stress on the tube and the rod.
Find the increase in these stresses when one nut is tightened by one quarter of a turn relative to the other. There are five threads per 10 mm. Take E = 200 kN\/mm2.
Solution:<\/p>\n\n\n\n
When nut is tightened, there will be compressive load on the tube which will be equal to the tensile load on the rod. Compressive stress cannot be equal to tensile stress because it depends on cross-section area and strength of the material.<\/p>\n\n\n\n
Pr = Pt = P,<\/p>\n\n\n\n
where Pr and Pt are loads on rod and tube, respectively.<\/p>\n\n\n\n
\u03c3rAr = \u03c3tAt,<\/p>\n\n\n\n
where \u03c3r and \u03c3t are tensile stress on rod and compressive stress on tube, respectively; and Ar and At are the cross-sectional areas of the rod and tube, respectively.<\/p>\n\n\n\n
Compressive stress on tube,
Tensile stress on rod, \u03c3r = 0.6875 \u03c3t = 0.6875 \u00d7 115.74 N\/m2 = 79.57 N\/mm2<\/p>\n\n\n\n
Let and be the stress due to tightening of nut by one quarter of a turn.
<\/p>\n\n\n\n
But, contraction in the tube + Extension in the rod = Axial movement of the nut<\/p>\n\n\n\n
Example 12.8: In Example 12.7, nut is removed and tube and rod are welded to washers and compressive load of 25 kN is applied on washers as shown in figure given below:<\/p>\n\n\n\n
Find the stresses in tube and rod.<\/p>\n\n\n\n
Solution:<\/p>\n\n\n\n
In this case change in length in tube and rod will be same as shown in Figure 12.15.<\/p>\n\n\n\n
Figure 12.15 Fixed End of Tube and Rod Assembly<\/p>\n\n\n\n
On solving Eqs (12.3) and (12.4), we get<\/p>\n\n\n\n
Example 12.9: A solid steel bar 0.5 m long and 0.07 m in diameter is placed inside an aluminium tube having 0.075 m inside diameter and 0.10 m outside diameter. The steel bar is 0.15 mm longer than the aluminium tube as shown in Figure 12.16. An axial load of 600 MN is applied to the bar and cylinder through rigid cover plate as shown in figure given below:<\/p>\n\n\n\n
Figure 12.16 Steel Bar and Aluminum Tube Assembly<\/p>\n\n\n\n
Find the stress developed in steel bar and cylinder through rigid cover plate.<\/p>\n\n\n\n
Solution:<\/p>\n\n\n\n
Let compression in tube is \u03b4lA1 m.<\/p>\n\n\n\n
Therefore, the compression in steel bar, \u03b4lsteel = \u03b4lA1 + (0.15 \u00d7 10\u22123) m.<\/p>\n\n\n\n
Total load on assembly = Load on tube + Load on steel bar = \u03c3A1 \u00d7 AA1 + \u03c3steel \u00d7 Asteel<\/p>\n\n\n\n
Example 12.10: A concrete column of 37.5 cm2 cross-section, reinforced with steel rods having a total cross-sectional area 7.5 cm2 carries a load of 800 kN as shown in Figure 12.17.<\/p>\n\n\n\n
Figure 12.17 Concrete Column<\/p>\n\n\n\n
If E for steel is 15 times greater than that of concrete, calculate the stresses produced in steel, and concrete.<\/p>\n\n\n\n
Solution:<\/p>\n\n\n\n
Contraction in both the steel and concrete will be same.<\/p>\n\n\n\n
From Eq. (12.5)<\/p>\n","protected":false},"excerpt":{"rendered":"
Consider a bar of varying cross-section of uniform strength subjected by a longitudinal stress \u03c3 as shown in Figure 12.10. Now consider a small element of axial length \u03b4x at a distance of x from smaller end. Let area of cross-section at section x be A and at section x + \u03b4x be A + […]<\/p>\n","protected":false},"author":1,"featured_media":2035,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[344],"tags":[],"class_list":["post-2037","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-strain-and-stress"],"jetpack_featured_media_url":"https:\/\/workhouse.sweetdishy.com\/wp-content\/uploads\/2024\/07\/download-18.jpeg","_links":{"self":[{"href":"https:\/\/workhouse.sweetdishy.com\/index.php\/wp-json\/wp\/v2\/posts\/2037","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/workhouse.sweetdishy.com\/index.php\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/workhouse.sweetdishy.com\/index.php\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/workhouse.sweetdishy.com\/index.php\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/workhouse.sweetdishy.com\/index.php\/wp-json\/wp\/v2\/comments?post=2037"}],"version-history":[{"count":1,"href":"https:\/\/workhouse.sweetdishy.com\/index.php\/wp-json\/wp\/v2\/posts\/2037\/revisions"}],"predecessor-version":[{"id":2038,"href":"https:\/\/workhouse.sweetdishy.com\/index.php\/wp-json\/wp\/v2\/posts\/2037\/revisions\/2038"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/workhouse.sweetdishy.com\/index.php\/wp-json\/wp\/v2\/media\/2035"}],"wp:attachment":[{"href":"https:\/\/workhouse.sweetdishy.com\/index.php\/wp-json\/wp\/v2\/media?parent=2037"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/workhouse.sweetdishy.com\/index.php\/wp-json\/wp\/v2\/categories?post=2037"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/workhouse.sweetdishy.com\/index.php\/wp-json\/wp\/v2\/tags?post=2037"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}